SLS and Multi Jet Fusion both turn nylon powder into strong, support-free parts, and on the bench the parts look alike. The differences show up in how many parts a system is built to produce, which materials and colors it can run, and what it costs to own. The choice usually comes down to three things: your weekly part volume, the materials and finish your parts need, and how much capital and floor space you can commit.
This guide compares the two processes factor by factor, then sets the printers side by side and ends with a part-by-part table of which process fits which application.
What each process is
Selective laser sintering (SLS) is a powder bed fusion process in which a laser scans each cross-section of a part across a heated bed of polymer powder, fusing it layer by layer. The unfused powder holds the parts in place, so no supports are needed and parts can be stacked through the whole build volume.
Multi Jet Fusion (MJF) is a powder bed fusion process in which an inkjet head prints a fusing agent where the part should be and a detailing agent along its edges, then infrared lamps pass over the whole layer and fuse the treated powder. MJF was developed by HP and remains a proprietary process, so all MJF printers come from a single manufacturer, while SLS printers are built by many.
The practical difference: SLS draws each layer with a laser, so layer time depends on how much area there is to scan. MJF treats the whole layer in one pass, so layer time stays roughly constant however full the layer is.
Part strength and consistency
Strength matters because powder bed parts are usually chosen for functional and end-use work, where a part that fails in service costs more than the part itself.
On this factor the two processes are closer to each other than either is to FDM. Both fuse powder across the full layer, both produce dense nylon with no weak bead-to-bead joints, and both are used for snap fits, living hinges, clips, housings and parts loaded from more than one direction. For the same polymer, PA12 for example, tensile strength from either process sits in the same range.
MJF’s broad infrared heating fuses the whole layer evenly, and service bureaus that run both processes generally report MJF parts as slightly more consistent between the XY plane and Z, with marginally higher elongation at break. That consistency is one reason MJF is popular for high-volume runs where every part in every build has to meet the same spec.
A well-controlled SLS process gives near-isotropic parts as well. Kinboshi, a Japanese manufacturer that added SLS alongside its FDM printers, drop-tested SLS parts from their working height and pressure-tested a 3 mm-wall pipe part at 1 MPa before committing, and the parts passed both. For most functional parts, design and material choice matter more than the choice between these two processes.
Accuracy, detail and surface finish
Accuracy and finish matter because they decide whether parts go straight into an assembly or need a fit check and finishing first.
A laser is a small, focused heat source, so SLS tends to hold slightly tighter dimensions on fine features and sharp edges. MJF’s detailing agent keeps edges crisp, but the lamps heat a wider area, and engineers who run both processes generally rate SLS as marginally more accurate and MJF as marginally stronger. Layer height follows the same pattern: MJF runs at a fixed layer of about 0.08 mm, while SLS systems can run layers from about 0.05 mm for fine detail up to thicker layers for speed.
Both processes leave a matte, slightly grainy surface, and both clean up well with bead blasting, tumbling or vapor smoothing. Color is the visible difference. Standard MJF parts come out grey, because the fusing agent is dark, and are usually dyed black as a separate step, with white available only on a dedicated white-material system. SLS color follows the powder: natural nylon comes out white and can be dyed, and black powders produce black parts with no dyeing step.
As with any powder bed process, accuracy depends on geometry, packing and cooling as much as on the machine, so the sound way to check either process is to print a representative part and measure it.
Materials and color
Material choice matters because heat resistance, chemical resistance, flexibility and certification come from the polymer, not the process.
Both processes run the core nylons: PA12, PA11 and glass-filled PA12. The differences sit at the edges of each list.
- MJF’s portfolio includes polypropylene (PP), a flame-retardant PA12, a white PA12 and TPU, each tied to specific printer models. PP’s chemical resistance and low moisture uptake, and the flame rating of PA12 FR, are the two properties that most often decide a project for MJF.
- SLS has the longer history and the wider range of nylon variants, including filled grades and TPU in softer hardnesses suited to padding, grippers and footwear. Many SLS systems are also open to third-party powders, so a team can qualify the exact grade an application needs, while MJF materials are developed and certified for HP’s platform.
In short, MJF has the edge for PP, flame-rated nylon and white parts. SLS has the edge for soft TPU, specialty nylon grades and freedom of powder supply.
Build volume and part size
Build volume matters because it caps the largest single part and sets how many parts share each build’s fixed costs.
Compact systems in both processes now sit in the 12 to 17 liter range, enough for parts up to roughly 220 to 350 mm depending on the axis. Production MJF systems build in about 380 × 284 × 380 mm, roughly 41 liters. Large industrial SLS systems go further, with build envelopes above 500 mm in at least one direction, which makes SLS the process of the two for the largest single parts.
The shape of the chamber matters as much as its volume. A tall, square chamber suits tall parts and stacked batches, while a long, shallow one suits long, flat parts. Check the longest axis of your largest part against each machine’s chamber, not just the liter figure.
Speed and throughput
Throughput matters because cost per part in any powder bed process falls as more parts share each build’s fixed costs: machine time, labor, energy and the powder that is heated but not used.
MJF’s whole-layer fusing is its biggest structural advantage. Layer time does not grow with how many parts are in the layer, so a densely packed build prints nearly as fast as a sparse one. A full production MJF build of about 41 liters takes around 12 hours, and those systems are positioned for hundreds of parts a week, with automation for unpacking and powder handling.
SLS layer time grows with the area the laser has to scan, so throughput depends on packing and laser power. A compact SLS system with a 75 W-class fiber laser produces in the region of 3 to 5 kg of finished parts per day, which covers tens to a few hundred parts a week for most part sizes. Larger SLS systems add more lasers to scale up.
Both processes use removable build units on most current systems, so a finished build cools outside the printer while the next one starts. Cooling takes several hours to about half a day, so a second build unit keeps the printer busy around the clock.
The practical split: if you produce the same parts by the hundreds every week, MJF’s production systems are built for that volume. If your weekly volume is lower or the part mix changes often, SLS delivers the output you need for far less capital.
Powder reuse and material cost
Powder reuse matters because unfused powder is heated in every build, ages, and has to be partly replaced with fresh powder, and that refresh is a running cost on every build.
This is where MJF has a clear advantage. MJF PA12 is rated for up to 80% reuse of surplus powder, so only a small share of fresh powder is added per build and waste stays low even on sparsely packed jobs. SLS nylons generally need a higher share of fresh powder per build, and the exact refresh ratio depends on the powder and the process window.
The powder itself costs about the same for both: nylon powders for either process are commonly priced around $100 per kilogram, with discounts at volume. The difference comes from how much of each build’s powder is consumed. On SLS, that makes full, well-nested builds more important. A well-packed build of small parts can bring cost per part down to around a dollar for a small clip, while the same printer running half-empty builds pays for powder it never uses.
Equipment cost and facility requirements
Equipment cost and facility matter because they decide whether in-house powder bed printing is a project the business can start this quarter or a capital program that needs a building plan.
Compact SLS systems now start from about $35,000 for the printer, with a production setup adding a second build unit, a depowdering station, a blasting station and dust extraction. They fit in a normal workshop with compressed air and a dedicated powder handling area.
Production MJF systems sit in a different capital class. They are quoted on application, a single spare build unit can cost around $30,000, and they need around 20 m² of operating area and about 12 kW of power. A compact MJF system has been announced at below $60,000 as a package, running on standard power, which brings MJF closer to the compact SLS price range.
For a team buying its first powder bed system, compact SLS costs less to start and offers a wider choice of powders. For a factory planning hundreds of identical parts a week with automation, production MJF justifies its price.
SLS vs MJF at a glance
| Factor | SLS | MJF |
|---|---|---|
| How a layer fuses | Laser scans each cross-section | Fusing agent printed, infrared lamps fuse the whole layer |
| Supports | None | None |
| Strength by direction | Near-isotropic | Near-isotropic, very consistent in Z at production scale |
| Dimensional accuracy | Slightly tighter on fine features | Slightly looser, crisp edges from the detailing agent |
| Layer height | About 0.05 mm and up | Fixed, about 0.08 mm |
| Surface as printed | Matte, fine grain | Matte, fine grain |
| Color | Follows the powder: white and dyeable, or black | Grey, usually dyed black, white on a dedicated system |
| Materials | PA12, PA11, filled nylons, TPU in several hardnesses, third-party powders on open systems | PA12, PA11, glass-filled PA12, PA12 FR, PP, white PA12, TPU |
| Largest builds | Above 500 mm in at least one axis on large industrial systems | About 380 × 284 × 380 mm |
| Throughput driver | Laser scan area and packing | Constant layer time, fastest on densely packed builds |
| Powder reuse | Refresh ratio depends on the powder | Up to 80% surplus reuse for PA12 |
| Supplier choice | Many manufacturers | One manufacturer |
| Entry cost | Compact systems from about $35,000 | Compact package announced below $60,000, production systems quoted on application |
| Best fit | In-house batches, mixed part work, R&D, soft TPU, specialty grades | High-volume production of the same parts, PP, flame-rated and white parts |
Raise3D SLS and HP MJF printers compared
The specifications of real machines show where each process sits today. The table compares Raise3D’s RMS220 SLS printer with HP’s compact MJF 1200 and its production Jet Fusion 5600.
| Factor | Raise3D RMS220 (SLS) | HP MJF 1200 (MJF) | HP Jet Fusion 5600 (MJF) |
|---|---|---|---|
| Build volume | 220 × 220 × 350 mm, 17 L | 320 × 165 × 230 mm, 12 L | 380 × 284 × 380 mm, about 41 L |
| Layer height | 0.05–0.40 mm | About 0.08 mm | About 0.09 mm |
| Materials | PA12, PA11, PA NEXT, PA NEXT GB, PA12 GB, TPU 86A and 90A, open-material option | PA12 at launch, more announced | PA12, PA11, PA12 GB, PA12 FR, PA12 S, PA12 W, TPU |
| Part color | Black nylon, black or white TPU | Grey | Grey or light grey |
| Output | 2.2 L/h at 20% packing, 3–5 kg/day | Full-height build typically under 12 hours | Up to 3,466 cm³/h, positioned for 550+ parts a week |
| Powder reuse | Depends on powder | Up to 80% for PA12 | Up to 80% for PA12 |
| Facility | Printer footprint about 0.58 m², compressed air, built-in nitrogen generator | Standard power, no separate gas supply | About 21.5 m² operating area, 12 kW |
| Price | $34,999 printer and one build unit | Package announced below $60,000 | Quoted on application |
| Availability | Shipping | Announced for early 2027 | Shipping |
In the compact class, the RMS220 offers more build volume and height, a wider material list including soft TPU, black parts and a lower entry price. The MJF 1200 offers higher powder reuse, a longer X axis for flat parts, and a path into HP’s production ecosystem. The 5600 is a factory machine for teams that will keep it full with hundreds of parts a week.
Which is better for which application
The application decides the process more reliably than any general rule, so the table below goes part by part.
| Application | Better fit | Why |
|---|---|---|
| Functional prototypes and small batches in-house | SLS | Lower entry cost, wide powder choice, flexible part mix |
| Black end-use parts | SLS | Black powder produces black parts with no dyeing step |
| Custom insoles, padding and soft grippers | SLS | TPU in softer hardnesses, dense nesting of mixed shapes |
| Tall housings and ducts | SLS | Taller compact chambers, large industrial systems for big parts |
| R&D labs testing several powders | SLS | Fast material changeover, third-party powders on open systems |
| Regulated parts that need one specific certified powder | SLS | Open systems let you qualify the exact grade |
| Hundreds of identical parts every week | MJF | Constant layer time, automation, high powder reuse |
| Fluid-handling parts and chemical-resistant housings | MJF | Polypropylene is available in the MJF portfolio |
| Flame-rated interior and electronics parts | MJF | Flame-retardant PA12 available as a standard material |
| White consumer and medical parts | MJF | White PA12 on a dedicated system, no painting |
| Long, flat parts in the compact class | MJF | Longer chamber axis on the compact system |
| Parts bought in rather than made in-house | MJF | Widely available at service bureaus at competitive prices |
Two patterns run through the table. SLS fits teams that want production nylon and TPU in-house with flexibility in materials and a modest budget. MJF fits factories running high volumes of the same parts, and parts that need PP, a flame rating or white nylon.
Frequently asked questions
Is MJF better than SLS?
Neither is better across the board. MJF leads on throughput at high volume, powder reuse and Z-axis consistency. SLS leads on material range, soft TPU, fine layers, supplier choice and cost of entry. For in-house batches of tens to hundreds of parts a week, SLS is usually the better value.
Are MJF parts stronger than SLS parts?
Only slightly, and not always. Both produce dense, near-isotropic nylon. MJF parts tend to be a little more consistent between directions and a little more ductile, while SLS tends to hold slightly tighter dimensions. For most functional parts, material and design matter more than the process.
Is MJF cheaper per part than SLS?
At high volume on production MJF systems, often yes, because layer time stays constant and most surplus powder is reused. At lower volumes, the cost of owning the system dominates, and compact SLS, with its lower entry price and per-part costs of around a dollar for small parts in full builds, is usually the cheaper route.
Can SLS print polypropylene like MJF?
PP is part of the MJF portfolio and is less common on SLS. If chemical resistance is the requirement, check whether PA12 or PA11 meets it before switching process, since both resist oils, fuels and many solvents.
Which is better for a first in-house powder bed printer?
For most teams, compact SLS. It costs less to start, runs a wider choice of powders, and fits a normal workshop. Compact MJF becomes an option for teams that need only PA12 and expect to grow into high-volume MJF production.
Do SLS and MJF parts need post-processing?
Yes, both. Parts are depowdered after cooling and usually bead blasted. MJF’s grey parts are commonly dyed black. SLS parts printed in black powder come out black, so blasting is often the only finishing step.
Conclusion
SLS and MJF produce parts that are closer to each other than most comparisons suggest. The real differences are scale, materials and capital. Production MJF is built for factories that print hundreds of the same parts every week, and it leads on throughput, powder reuse, PP, flame-rated PA12 and white parts.
For teams that want production-quality nylon and TPU parts in-house without a factory budget, SLS is the more practical route, with a lower entry cost, more powder choice and more flexibility in what each build carries. If your weekly volume, part mix or material needs point that way, Raise3D’s application engineers can print sample SLS parts from your CAD files so you can check strength, finish and cost on your own parts before deciding.