Introducing the New Raise3D T Series of FFF Printers
- Added support for the new Raise3D T Series printers (Raise3D T450 and Raise3D T700), including nozzle sizes, the TwinFlow™ two-in-one-out flow mode, materials, and slicing templates.
- TwinFlow™ High Flow Mode: Both sides feed and extrude simultaneously, increasing extrusion throughput and improving single-material printing efficiency.
- Printer information synchronization: Sync the printer and nozzle size with one click.
- Select a T450 or T700 printer to display the Sync button.

- If no printer has been connected, you will be prompted to connect one from the Remote interface.

- After connecting a T450 or T700, click Sync. When synchronization succeeds, a confirmation appears and asks whether you also want to sync materials.
- Material synchronization: Materials can be synced using Mapping or Overwriting mode.
- In Mapping mode, materials in the local Prepare to Slice panel are mapped to materials on the remote printer.
- In the example below, all materials on the remote printer are HS-PLA and cannot be matched to the local materials, so they are shown as Unmapped.
- Add unused materials: Also add materials on the printer that have not been mapped to the Prepare to Slice panel.
- Automatically merge the same materials: Merge identical materials into one material.

- In Overwriting mode, the printer’s materials directly replace the materials in the Prepare to Slice panel.
- After synchronization in the example below, the Prepare to Slice panel will show only two materials, both HS-PLA. Their colors will also be replaced with the colors configured on the printer.


- Remote Print Initiation and Material Mapping
- Upload the sliced file and send the material mapping to the printer, which then starts the print.
- Click Upload to Printer. For FFF printers, the materials configured on the printer are displayed. If the materials can be mapped successfully, you can print directly; otherwise, you can only upload the file.

- Remote connection: Remotely view print job status and live camera footage, and access relevant controls.
- Remote printing desktop notifications: Receive real-time updates when a print job’s status changes.
- For detailed instructions, see the T Series Slicing Workflow Guide. [Help document link to be added.]
Raise3D RMS220 Maximum Print Height Increased to 450 mm
- The RMS220 maximum print height has been increased from 350 mm to 450 mm, enabling slicing and printing of taller models.
Note: Users upgrading to the new version must reset their RMS220 printer settings before the new maximum print height takes effect.
New and Improved FFF Features
1. Independent Slicing Template Control for Each Material
- Material-level template configuration and control
- Slicing templates can now be configured and controlled separately for each material, for both multi-input, single-output printers and other printer configurations.
- Manually enable Use Template (disabled by default) to activate the independent template menu and shortcut controls for the corresponding material.
- When independent template control is enabled, the slicing template dialog automatically hides the previous right-nozzle settings to reduce interface clutter and avoid configuration conflicts.
- Material-specific slicing parameters for multi-material printing
- Starting with the second material, the following key slicing parameters can be applied independently to each material to accommodate different processing requirements when printing multiple materials together:
- Extrusion and geometry: extrusion width, Flowrate, and Extruder settings.
- Speed and motion: print speeds for different feature types, travel speed, maximum volumetric flow rate, acceleration, and jerk.
- Temperature control and pressure compensation: printing temperature, bridge and overhang fan speeds, and Pressure Advance.
- Starting with the second material, the following key slicing parameters can be applied independently to each material to accommodate different processing requirements when printing multiple materials together:

2. Support for a New GCode File Type: FFFCode
- Significantly reduces the size of sliced print files for FFF printers.
- Reduces print file transfer time.
- Makes it easier for the printer to parse the information it needs.
- The default file format exported when slicing for the current printer can be changed in Printer Settings.

3. New Overhang Detection Algorithm
- A new overhang detection method calculates the proportion of an individual extrusion line that extends beyond the layer below (Unsupported Ratio). This identifies overhang regions more accurately and automatically adjusts print speed, significantly improving the quality of overhangs and bridges.
- Use Overhang Shells Mode to switch between the new and previous algorithms.
- Shell Speed Smoothing is recommended when using this option.

- With Overhang Shells Mode set to Unsupported Ratio, most overhang transitions are uniform, with fewer abrupt speed changes.

- With Overhang Shells Mode set to Angle, overhang transitions are uneven and speed changes are abrupt.

4. Shell Speed Smoothing
- A smoothing coefficient controls rapid changes in inner and outer shell speeds. Combined with the overhang detection algorithm, it reduces abrupt speed transitions and improves model surface quality.
- Use this option with the new overhang detection algorithm.

- Shell Speed Smoothing enabled, Coefficient = 80: speed changes from 10 → 45 → 106 → 193 → 200 mm/s.

- Shell Speed Smoothing disabled: speed jumps directly from 10 to 200 mm/s.

5. Shell Speed Smoothing Along Z
- Smooths outer shell print speeds across adjacent layers along the Z axis, reducing abrupt changes between layers and improving the consistency of the model’s side surfaces.

- Shell Speed Smoothing Along Z enabled

- Shell Speed Smoothing Along Z disabled

6. Filter Out Small Overhangs
- Enable Remove Support under Small Overhangs to prevent support generation under small overhangs. This avoids unnecessary tiny support structures, saving material and support-removal time while maintaining print quality.
- Option enabled:

- Option disabled:

7. Remove Support under Bridges
- Enable Remove Support under Bridges to prevent support generation beneath bridges, reducing unnecessary support material and print time.
- Option enabled:

- Option disabled:

- Note: Supports are still retained for relatively long bridges:

8. Detect Floating Solid Fill
- The new Detect Floating Solid Fill and Floating Solid Fill Speed settings allow floating solid fill regions to be printed at a lower speed, improving their printing stability.

9. New Travel Path Algorithm
- The travel path algorithm has been redesigned to preferentially route travel moves along the model’s inner shells rather than its outer shell, reducing scratches and defects on exterior surfaces.
- Travel path calculation time is also reduced by 20–30%, improving slicing efficiency.


- Avoid Traveling Through Printed Parts
- New travel-routing options, including Avoid Traveling Through Printed Parts Offset, control how travel moves are routed:
- Avoid traveling through printed areas and control the corresponding horizontal clearance.
- Where possible, route travel moves along sparse infill extrusion lines.
- When the option is enabled, travel moves while printing supports will generally no longer pass through the hole in the center of the model below:

- With Avoid Traveling Through Printed Parts Offset set to 5 mm, the clearance between travel paths and the model increases.

- With Snap travel moves onto infill lines enabled, travel paths follow infill lines, so any oozing occurs on already-printed sparse infill. However, the travel path becomes considerably longer, substantially increasing print time.

11. Improved Internal Bridging Algorithm
- Based on the sparse infill distribution in the previous layer, internal bridge paths are preferentially anchored to the sparse infill.
- This significantly reduces sagging caused by insufficient support under bridges in previous versions and improves the quality of internal transitions. Print time may increase slightly.
12. Preserve Painting After Cutting or Reloading
- When a painted model is cut or reloaded, its existing surface painting data is automatically retained, eliminating the need to repaint it.
- Enable Preserve painting across mesh edits (experimental) in Preferences.
Performance Improvements
1. Reduced Memory and GPU Memory Usage in Sliced File Preview
- Significantly reduced loading time for sliced file previews.
- Significantly reduced peak memory usage, GPU memory usage, and overall memory consumption.
- Significantly faster rendering in Speed and Volumetric Flow Rate preview modes.
2. Optimized Instance Handling in FFF Slicing
- Optimized instance handling in FFF slicing to significantly speed up slice generation when models are duplicated in batches and reduce memory usage when working with many instances.
Material and Slicing Templates
1. New Raise3D T450 and Raise3D T700 Printers and Templates
- Initial release
- The Raise3D T450 includes a total of 14 materials and slicing templates for 0.4 mm and 0.6 mm nozzles.
- The T700 includes a total of 14 materials and slicing templates for the 0.4 mm nozzle.
2. New Resin Templates for Raise3D DF2+
- [Raise3D] High Detail Apricot V1, 0.05 mm – Standard, V1.1 and 0.05 mm – Speed, V1.0
- [Raise3D] Tough 2K Grey V1,05mm-Standard, V1.0
- [Raise3D] Draft Grey V1,1mm-Standard, V1.2
- [Raise3D] ESD Black V1,05mm-Standard, V1.2
3. Added RMS220 Material Templates
- Printer settings update: The maximum print height has been increased to 450.00 mm, and the corner radius of the maximum printable area has been adjusted to 10.00 mm.
- Slicing template updates: The preheating process, insulating layer, and annealing parameters have been optimized to improve temperature stability and print quality. Random contour start points are now enabled by default to eliminate a fixed seam on the surface.
- [Raise3D] PA NEXT Black V1,12mm – Standard – Nitrogen, V1.2
- [Raise3D] PA NEXT GB Black V1,12mm – Standard – Nitrogen, V1.1
- [Raise3D] PA11 Black V1,12mm – Standard – Nitrogen, V1.1
- [Raise3D] PA12 Black V1,12mm – Standard – Nitrogen, V1.1
- New slicing template:
- [Raise3D] PA12 Black V1,12mm – Standard – Air, V1.1
4. Built-in Third-Party Resin Templates
- To further expand the resin printing materials ecosystem, ideaMaker now includes 54 slicing templates developed and validated by Liqcreate:
- DF2: 19 new printer-specific material slicing templates.
- DF2+: 35 new printer-specific material slicing templates.
Other Improvements
- Overhang Shell Display in GCode Preview
- In Structure render mode, overhang shells are displayed in a distinct color.
- Overhang shells are displayed only when Overhang Shells Mode is set to Unsupported Ratio.
- Removed the entry point for 2D preview.

- Preferences Changes
- Removed the following options and their associated functionality:
- Visualize GCode by traces without emulating extrusion width in 2D mode
- Visualize GCode by traces without emulating extrusion width in 3D mode
- Added Enable instanced rendering for GCode preview (experimental).
- Removed the following options and their associated functionality:
- Improved the interaction for deleting models within a group in the model list.
Bug Fixes
- Fixed SLS level-of-detail (LOD) strategy and rendering issues.
- Fixed an FFF first-layer preview issue.