+1 888 963 9028

Tough 2K Resin

Strong and tough applications

Tough 2K Resin is a tough and strong material with excellent ductility, toughness and impact resistance. As a result, it is ideally suitable for end-use parts where performance and durability are needed.

Tough 2K Resin exhibits strength and rigidity similar to ABS, and its excellent toughness and impact resistance make it suitable for a variety of performance prototyping and tooling applications, including strong and tough prototypes, end-use parts, jigs and fixtures, and manufacturing aids.

Raise3D Tough 2K Grey Resin 1kg

Order Now

Features

  • 45 MPa tensile strength
  • 35% elongation at break
  • 31 J/m Izod notched impact
  • 2158 MPa Young’s modulus
  • 68°C HDT @ 0.45 MPa

Benefits

  • Tough and strong
  • Excellent toughness and impact resistance
  • Strength and rigidity similar to ABS

Applications

  • Strong and stiff prototypes
  • Jigs and fixtures
  • Manufacturing aids
  • Housings and enclosures

Material Properties*

*All test specimens were printed in 100 μm thickness with Raise3D DF2 printer (2 mW/cm2 at 405 nm, 100 μm thickness, 14s) and cured with DF Cure for 20 minutes per side at room temperature.
See more details in Technical Data Sheet.

Testing Method Green Post-Cured
Tensile Strength ASTM D638 25 MPa 45 MPa
Young’s Modulus ASTM D638 1334 MPa 2158 MPa
Elongation at Break ASTM D638 59% 35%
Flexural Strength ASTM D790 53 MPa 90 MPa
Flexural Modulus ASTM D790 1347 MPa 2315 MPa
Notched Izod ASTM D256 36 J/m 31 J/m
Heat Deflection Temp.@0.45 MPa ASTM D648 N/A 68°C

 

Compare Resins Properties

Compare the resins’ properties, and find the one that best meets your requirement.

Printing Settings

It is recommended to use the default printing profiles available in ideaMaker.

After printing, it’s recommended to not leave a successful but unwashed model in the printer for too long. This will prevent the model from over-swelling, which may cause dimensional deviations or support softening.

For more printing information, please read Raise3D DF2 3D Printer User Manual.

Cleaning

Tough 2K Grey V1 Resin requires cleaning to achieve the ideal properties of the printed part.

There is no need to remove support structures from the printed part, and the part should then be washed before post-curing, until the surface is free of any solvent residue.

For special structures or fine details, such as small holes, it’s recommended to clean manually, and then blow dry the part with compressed air/nitrogen to remove residual solvent from the surface. Or leave the part for a short time at room temperature to dry. Post-cure the model until the surface is free of any solvent residue.

Please refer to the chart on the right for the recommended washing parameters with Raise3D DF Wash.

Wash Time Wash Drying Time
Recommended washing parameters 10 min 10 min

 

Post-curing

After cleaning, Tough 2K Grey V1 parts requires post-curing to achieve optimal properties. Please refer to the chart on the right for the parameters with Raise3D DF Cure.

Setting 1: For prototyping uses.

Setting 2: To achieve the best resin properties, as indicated in the TDS (default parameters in ideaMaker).

UV Curing Time Heat Curing Time Heat Curing Temperature
Setting 1 3 min 3 min 60℃
Setting 2 40 min 0 min N/A

 

Download Product Documents

Tough 2K Resin

Learn more about Raise3D resins

Learn More